Designed to suit the maintenance of CeramicSpeed Bearings, the CeramicSpeed All Round Grease maximizes your bearings' lifetime and performance. This type of grease is a low-to-medium viscosity lubricant and works as the best compromise between friction influence and lifetime. We recommend it for optimal use in dry and sunny weather conditions, where no or very little contamination threatens the bearing. The application covers mostly road riding conditions; however, it can be used off-road in the same weather settings, on all types of CeramicSpeed Bearings. When lubricating your bearings, we recommend a fill rate of 60-80%. - The CeramicSpeed All Round Grease comes in a 10ml syringe - For use in CeramicSpeed Wheel Bearings and Bottom Bracket Bearings - Can be used for added durability in pulley wheels when used in adverse weather conditions - 5,000-10,000km or 3,000-5,000 mile average lifespan in clean conditions - 1,000-3,000km or 600-1,800 mile average lifespan in wet and harsh conditions
We focused on maximizing your performance and the longevity of your CeramicSpeed Pulley Wheels when we designed the special oil for pulley maintenance. Remember to add oil on the outside of the bearing seal after riding in wet conditions or washing your bike. If you are riding in harsh and wet conditions, we recommend that you choose the All Round Grease instead and grease your bearings from time to time. When using the oil for maintenance, the recommended dose is 1-2 drops. Remember that the OSPW System has two lubrication points on the back cage plate to facilitate this process.
We call it LongLife because this grease delivers the best protection and lifetime for your bearings, even in the most harsh riding conditions. This is the best choice if you spend your time riding your bike in a humid environment and you do not use coated bearings or if your cycling application is an off-road discipline. Be aware that the LongLife grease has a slightly higher friction coefficient than the standard All Round grease. This is a medium-viscosity type of grease, designed to deliver the best performance under the worst riding conditions. The recommended fill rate is 70-100%, depending on the weather conditions and riding application. - For use in CeramicSpeed Wheel Bearings, Bottom Bracket Bearings, and Headset Bearings - 8,000-13,000km or 5,000-8,000 mile average lifespan in clean conditions - 3,000-8,000km or 1,800-5,000 mile average lifespan in wet and harsh conditions - 10ml syringe
CeramicSpeed Time Trial / Track Grease is a great choice when riding short time trials or track, designed to deliver as low friction as possible, thanks to the Dynamic Viscosity Transformation (DVT) technology used in its formula. When the TT Grease lubricating film is subject to the high pressure at the point of contact between the ball and race, the TT Grease instantly changes its state to a lower kinematic viscosity, similar to that of a light oil. The DVT technology provides the best of both worlds for the rider—the low friction properties of a light oil combined with the longevity of a light grease. This grease is ideal for ceramic bearings and is suitable for steel bearings as well. When greasing the bearings, the recommended fill rate on road is 25-30% and on track 15-20%. Re-lubrication is required more frequently when using TT+Track grease. - For use in CeramicSpeed Wheel Bearings and Bottom Bracket Bearings - 1,000-2,000km or 600-1,200 miles optimal efficiency - Developed exclusively for performance—no protection benefit - 10ml syringe
The CeramicSpeed UFO Clean Drivetrain thoroughly removes grease and grime from all drivetrain components. The unique properties dissolve wax from internal rollers and all surfaces of chain links. UFO Clean Drivetrain is designed and formulated to clean and prepare chains for wax coatings, using the same formula that we at CeramicSpeed use to prepare our UFO Chains. This is a non-toxic and biodegradable formula—environmentally friendly and safe. - Non-toxic and biodegradable formula - Thoroughly removes grease and grime from all drivetrain components - Developed and bottled in Denmark - Avoid applying directly to disc brake pads - Contains 1 liter - Not to be used as a bearing cleaner - Safe for carbon, glossy- or matte-painted, and anodized surfaces
Page 1 of 1