Filter By:
Workstands
$7.73
The 1971 installs onto the clamps found on most Park Tool repair stands to more securely hold D-shaped seatposts by converting one jaw profile to a flat surface. This is useful for bikes with D-shaped seatposts and other non-traditional designs that would cause a less-than-ideal fit in traditional repair stand jaws. The 1971 is designed to fit over a clamp's existing jaw covers and is easy to remove and install by hand, making it a convenient accessory for your repair stand.
Compatible with the following repair stands:
- PCS-9.2 and PCS-9.3
- PCS-10.2 and PCS-10.3
- 100-3D Micro-Adjust Clamp, as found on PRS-2.2, PRS-2.3, PRS-3.2, PRS-3.3, PRS-33.2
- 100-5D Micro-Adjust Clamp, as found on PCS-4
- 100-25D Micro-Adjust Clamp, as found on PRS-25 and PRS-26
$9.90 - $18.95
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp:
- 1002: fits 100-3X and 100-5X extreme range clamps
- 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12
- 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps
- 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps
- 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps
- 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current)
- 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C)
- 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands)
- 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
$13.95
Park Tool's Tool Tray Collar easily adapts the #106 Work Tray to fit the 41mm upright tube on 2011 and older PRS-20 and PRS-21 Repair Stands, as well as 1996 and newer PCS-1, PCS-4, PCS-4-1 and PCS-4-2 Repair Stands (each sold separately).
$14.95
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
$14.99
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
$19.95
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease.
- Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3
- Easily removed and installed with hook-and-loop material
$19.99
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
$25.95
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
$25.95
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
$34.95
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
$34.95
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps.
Includes:
• 118s adjusting barrel
• 117s eyebolt
• 121s adjusting barrel pivot
• 136 nut
• 116s cap screws (2)
• 108s-2 pins (2)
• 107s-2 pin (1)
• Washers (3)
• E-clips (3)
$35.95
The Tilting Base fits Park's TS-2 Professional Wheel Truing Stand (sold separately). It allows adjusting the truing stand 20 degrees forward or backward for comfortable use at any bench height. The handy front bins hold Park Spoke Wrenches (sold separately) and other small items such as nipples. Rounded bin corners make even the smallest parts easy to retrieve. The base's reinforced nylon body stands up to heavy use and has holes for mounting to a workbench for stability.
$38.50
All Feedback Sports repair stands are designed to be excellent at home and excel in the field. The Tool Tray add-on is the ultimate service partner for the most demanding mechanics. It’s lightweight and durable design delivers easy access to tools, lubricants, spare components and accessories during tune-ups or bike washing sessions. With a towel hook, drain ports, compartmentalized tool holders and a spot for your coffee mug or adult beverage, what else could a bike mechanic need?
$42.00
Feedback Sports repair stands are the ultimate portable and home service partner for the most demanding mechanics. They’re ultralight, compact, and durable design delivers unmatched stability, adjustability and portability. Our Travel Bag collection is an awesome travel and protective companion for ensuring your stand looks new for years to come. Be the most popular rider at the trailhead with a Feedback Sports repair stand. Be the most popular mechanic at home with a brilliant storage bag.
- Maximize the portability of your Feedback Sports repair stand
- Protect your stand’s aluminum finish and your other equipment when traveling
- Travel bag is water-resistant, durable and padded
- Enough space for a Sprint Repair Stand and a Flop Stop
- External window for business cards / ID card
- Padded Velcro strap for comfortable carrying and transport
- Full length, dual-zipper design
- Rugged end-loops for vertical storage when not in use
- 1-Year Warranty
$44.99
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
$49.99
The PCS-EXT is an extension that adds up to 21 inches (53 cm) of adjustable working height to any PCS-1 or PCS-4 repair stand manufactured between June 1996 and December 2001. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC Accessory Collar.
$52.99
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
$55.95
Park's Truing Stand Upright Extensions are made of durable chrome-plated steel and have quick-releases so they install in seconds to your Park TS-2 Professional Truing Stand (sold separately). The Uprights allow the stand to be used with wheels with hubs up to 160mm wide (found on some tandems and downhill bikes), and 29-inch mountain-bike wheels. Plus, there are specially sized bosses that act as adapters to hold wheels with 20mm through-axle hubs, too.
$59.95
Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
$62.99
Park's Sliding Through-Axle Adapter converts their PRS-20, PRS-21 and PRS-23 repair stand (sold separately) to accept 15mm and 20mm through-axle wheeled bikes. Use your axle to mount your bike. One side of the adapter is for 15mm axles, the other for 20mm.
$62.99
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
$66.00
The A-Frame is a versatile bike storage resource for up to 8 bikes and as the industry standard you’ll see one (or twenty) at practically every cycling event. Making contact with only the bottom of your seat, the A-Frame is the best bike parking solution for expensive road, cyclocross, mountain bikes, electric bikes and even kids bikes. And when the day is done it folds up and stores easily in a compact travel bag. Add this accessory A-Frame Center Post to retrofit any generation A-Frame when heavier mountain bikes or electric bikes are present!
Features:
- Center Post significantly increases overall weight capacity of the A-Frame*
- Ideal for E-Bikes and Trail/DH mountain bikes
- Updated Speed Fitting quick-release style hardware makes setup faster and more convenient than ever
- Rubber-coated end adds stability on concrete and other smooth surfaces
- Ideal bicycle storage space for bike races, gran fondos, triathlons, demo events or community cycling events
- Versatile design allows for bike parking without risk of scratching bikes or damaging components
- System fits most any road bike, cyclocross bike, mountain bike, fitness bike, electric bike, or kids bikes
- Innovative design easily folds to a compact unit when not in use
- Tool-free design makes setup and breakdown quick
- Anodized 6000-series aluminum body is lightweight, corrosion resistant and incredibly durable
- Provides an awesome bike parking solution for up to 400lbs (180kg) of bikes*
- Total width safely accommodates up to 8 bikes (not to exceed 400lbs / 180kg*)
- 3-Year Warranty
*Listed weight capacities are a reflection of proper setup on level ground
$68.95
Park's Cast Aluminum Tool Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools, lubes and small parts close at hand. It has deep sides so your small items stay put, a holder for cans of lube and slots for holding your tools. This handy tool fits Park's PRS-2, PRS-3, PRS-6, PRS-13, PCS-1, PCS-1 and PCS-4 repair stands manufactured after June 1996 (stands sold separately).
$109.95
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height.
- 19 tool holding holes, slots and small trays in a variety of shapes and sizes
- 14-inch (35cm) magnetic tool bar
- Integrated mounting holes for PTH-1 Paper Towel Holder
- Phone/tablet/clipboard holder
- Pen and pencil holders
- Adjustable utility hook to hang wheels, parts and scales
- Height adjustable
- Can be installed on a fully assembled stand
$109.95
Topeak's LineUp Stand securely holds your bike by the rear wheel for storage or display. Its spring-loaded arm automatically adjusts to fit wheels from 20-inches to 29-inches in diameter. Use it at home to store your bike, or use it to hold your pit bike at your next cross race!
$113.66
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
$119.95
Park's Home Mechanic Wheel Truing Stand allows extremely accurate and reliable wheel truing and even building at an economical price. It's constructed from heavy-gauge steel and works with most wheel sizes and hub widths. It can be bolted to a bench for additional stability.
$125.95
Park's Bench Mount Home Mechanic Repair Stand features a quick adjusting cam-type clamp that fits on frame tubes up to 76mm in diameter. Plus, the clamp rotates 360 degrees for access to any part of the bike for easy repairs. The clamping pressure is fully adjustable, too, to prevent damage to lightweight frame tubes. Plus, this excellent stand boasts a durable powdercoat finish, protective rubber jaws, and it mounts to any flat surface (bolts sold separately), so you can turn just about any nook and cranny in your house or garage into a proper bike repair facility!
$154.95
The Home Mechanic Repair Stand offers Park Tool quality in an entry-level repair stand for home mechanics. The 3-point leg system and adjustable height (from 39 to 57 inches) create a stable, ergonomic repair station for easy, efficient wrenching. Plus, the great clamp fits seatposts and frame tubes from 7/8 to 3 inches in diameter, has replaceable protective rubber jaws and rotates 360 degrees for easy access to all parts of your bike. It will also clamp round and aero seatposts. This stand even folds to 41 inches for easy portability and storage.
$164.95
A bench-mounted version of our popular PCS-10.2 Deluxe Home Mechanic Repair Stand. Features our world-famous cam-actuated micro adjust clamp design, which securely holds bicycles in place while allowing quick installation and removal.
- Cam actuated, micro-adjustable clamp allows quick entry and exit and fits 1-inch to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material
- Narrow clamping jaws (2.7-inch/7cm) fit into tight areas or on short seat posts
- 360° infinite clamp rotation allows bike to placed in optimal position for specific repairs
- All-steel structure for maximum stiffness and durability
- Super strong glass-filled nylon-composite fittings and top tube internals enable smooth rotation and secure positioning
- Mounts to any flat surface (mounting bolts not included)
Distance from the center of the clamp to the center of the mount is approximately 11 3/4-inch (30cm). Height from bench to center of the clamp axis is approximately 9 7/8-inch (25cm).
Weight Limit: The PCS-12.2 Home Mechanic Bench Mount Repair Stand has an 80 lb. (36kg) weight limit, provided the stand is securely mounted with appropriate fasteners to a solid and secure bench surface. The user is responsible for making sure the workbench and the fasteners are capable of handling this amount of weight.
Page 1 of 3
Next page